Data Center Foundation Exam -1

 Q1 - Which two devices would you choose to be a part of the core layer in the three-tier network design? (Choose two.)

Top of Form

• Cisco Nexus 9500 Series Switch
• Cisco Catalyst 9800 Series Switch
• Cisco UCS 6200 Series Fabric Interconnect
• hypervisor
• Cisco Nexus 9300 Series Switch

Ans – Cisco Nexus 9500 Series Switch and Cisco Catalyst 9800 Series Switch

 

Q2 - Which option lists the three tiers of a three-tier architecture?

Top of Form

• core, aggregation, and access
• core, spine, and leaf
• base, spine, and leaf
• physical, data link, and networkBottom of Form

Ans - core, aggregation, and access

 

Q3 - Cisco Unified Data Center is based on which three pillars of Cisco innovation? (Choose three.)

Top of Form

• Cisco Unified Computing System
• Cisco Unified Fabric
• Cisco Unified Access
• Cisco Unified Communications
• Cisco Unified Management
• Cisco Overlay Transport Virtualization
• Cisco FabricPath

Ans  - Cisco Unified Management, Cisco Unified Computing System and Cisco Unified Fabric

 

Q3- Which device would you choose to be a part of the core layer in a three-tier network design?

·       Cisco UCS 6400 Series Fabric Interconnect

·       Cisco Nexus 9500, Cisco Catalyst 6800, or Cisco Catalyst 6500 Series Switch

·       hypervisor

·       Cisco ASA security appliance

Ans - Cisco Nexus 9500, Cisco Catalyst 6800, or Cisco Catalyst 6500 Series Switch

 

Note - It is estimated that a spine-and-leaf model allows for 25 percent greater scalability over a three-tier model when used for data center designs.

·       Scalability - If oversubscription of a link occurs, the process for expanding capacity is straightforward. You can add an extra spine switch and extend uplinks to every leaf switch, resulting in the addition of interlayer bandwidth and reduction of the oversubscription. If device port capacity becomes a concern, you can add a new leaf switch by connecting it to every spine switch and adding the network configuration to the switch.

·       Low Latency - With a spine-and-leaf architecture, the traffic crosses the same number of devices to get to another server, regardless of the server to which the leaf switch is connected. This approach keeps latency at a predictable level because a payload only must hop to a spine switch and another leaf switch to reach its destination.

 

Q4 - Which option describes the topology design in a spine-and-leaf network?

Top of Form

• The design uses a partial mesh of links at the leaf layer.
• The design uses a full mesh of links between the leaf and aggregation layers.
• The design uses a full mesh of links between the spine and leaf layers.
• The design uses a full mesh of links at the leaf layer.Bottom of Form

Ans - The design uses a full mesh of links between the spine and leaf layers.

 

Note - Converged solutions on the market:

• FlexPod (Cisco and NetApp)
• FlashStack (Cisco and Pure Storage)
• Hitachi Adaptive Solutions for CI (Cisco and Hitachi)

 

Q5 - What are three benefits of the two-tier storage network design? (Choose three.)

Top of Form

• It is recommended for larger storage environments.
• It is elastic in case of failures.
• It is recommended for small-to-medium–sized environments.
• It is redundant through dual-fabric design.
• It is very expensive.
• It is a single point of failure.
• It is optimum for IP storage.

Ans – A. It is recommended for larger storage environments. B. It is elastic in case of failures. C. It is redundant through dual-fabric design.

 

Note - In most hyperconverged solutions, the minimum size group is three servers (commonly referred to as nodes).

Nutanix - Each server appliance contains three software layers:

• Server firmware: Cisco UCS
• Hypervisor: Nutanix Acropolis Hypervisor (AHV) or vSphere ESXi
• Hyperconverged storage software: Nutanix Acropolis Operating System (AOS)

Q6 - Which statement about Cisco Compute Hyperconverged with Nutanix is correct?

Top of Form

• It provides network connectivity with the Cisco Nexus 9500 series switches.
• Hardware compute platforms used in Cisco Compute Hyperconverged with Nutanix are Cisco UCS blade servers.
• The Cisco Compute Hyperconverged with Nutanix solution is a combination of hardware and software.
• It uses SAN protocols like Fibre Channel and iSCSI for server addition and retiringBottom of Form.

 

Ans - The Cisco Compute Hyperconverged with Nutanix solution is a combination of hardware and software.

Q7 - Cisco Unified Data Center infrastructure eliminates tiered silos and allows consolidation of which option?

Top of Form

• LAN and WAN
• LAN and SAN
• LAN and WLAN
• performance and security management

Bottom of Form

Ans – LAN and SAN

 

Q8 - In a spine-and-leaf topology, what is the minimum number of spines if redundancy is taken into consideration?

Top of Form

• one
• two
• four
• six

Bottom of Form

Ans -Two

 

Q9 - Top of Form

What are two benefits of the SAN storage network design? (Choose two.)

Top of Form

• Allows for easier maintenance of servers.
• It is redundant through dual-fabric design.
• It is very affordable.
• It is a single point of failure.
• It is optimum for IP storage.

Ans – A. Allows for easier maintenance of servers. B. It is redundant through dual-fabric design.

Q10 - Which are the three characteristics of a hyperconverged storage system? (Choose three.)

Top of Form

• easy expansion
• no SAN network
• usage of multiple storage arrays
• usage of redundant SAN switches
• easy deployment and maintenance
• fast convergence

Ans – A. easy expansion B. no SAN network C. easy deployment and maintenance

 

Q11 - Which option lists the two tiers of a Clos-collapsed core architecture?

Top of Form

• aggregation and access
• spine and leaf
• spine and access
• collapsed core and leaf

Bottom of Form

Ans – Spine and LeafQqBottom of Form

 

 

Q12 - You are working in the IT department of a small banking company that needs a new storage solution. The IT infrastructure consists of a single Cisco UCS server that hosts five VMs. Soon, the company will expand, a new server will be added, and a centralized storage array will be needed. Which network design approach is required in this case?

Top of Form

• cloud storage solution
• three-tier network with Cisco MDS multilayer switches
• directly attached network
• storage area network

Bottom of Form

Ans –

 

Q13 - If you are running out of physical ports, which action should you take to increase physical connectivity for end devices?

Top of Form

• Add an additional core switch and directly connect it to each leaf switch.
• Add an additional core switch and directly connect it to each core switch.
• Add an additional leaf switch and directly connect it to each core switch.
• Add an additional leaf switch and directly connect it to each leaf switch.

Ans- Add an additional leaf switch and directly connect it to each core switch.